Kernel 2.6.32 from Samsung Acclaim R880 on Spica

**gotenks** · 01-23-2011, 07:07 PM

Hi Spica kernel developers,

I've made an attempt to compile and run kernel from Samsung Acclaim R880 on a Spica.

Unlike criminal, I've taken a different approach to do that. Since Acclaim is "almost Spica" in terms of hardware design and components, I decided to use pure Acclaim sources, including modules, except dpram module, which seems to be responsible for initialising and comunicating with modem cpu. I've also used xsr modules and init from Acclaim (although I am not sure I should - see below).

After a little "fight", the kernel runs, but it stops at displaying STANDARD Android tekst "A N D R O I D", instead of usual Samsung logo, which used to be displayed with normal kernels on my phone (only if the phone is not connected to PC during boot process - see below). And I am stuck here.
I am stuck, because there seems to be a problem with handling Spica USB with Acclaim's kernel. If I try to boot with phone connected to PC either with normal cable or "serial" cable (JIG + TTY->RS232) the phone reboots here (output below) (instead of going forward to display "A N D R O I D") :

Code:

....
[    4.019124] S3C FIMC v3.0
[    4.020246] aat1271a_flash_init
[    4.024413] S3C6400 MFC Driver, (c) 2007 Samsung Electronics
[    4.033395] S3C6400 MFC driver module init OK.
[    4.033441] S3C PostProcessor Driver v3.12, (c) 2009 Samsung Electronics
[    4.041923] S3C JPEG Driver, (c) 2007 Samsung Electronics
[    4.048217] S3C G3D Driver, (c) 2007-2009 Samsung Electronics
[    4.052123] s3c_g3d version : 0x1050000
[    4.054539] G3D_RESERVED_MEM_SIZE : 32 MB
[    4.058648] G3D_CHUNK_SIZE : 1 MB
[    4.061868] G3D_CHUNK_NUM : 32 (UI_CHUNK:4)
[    4.066028] 0 th virt_addr = 0xcb000000, phy_addr = 0x5b000000
[    4.071823] 1 th virt_addr = 0xcb100000, phy_addr = 0x5b100000
[    4.077627] 2 th virt_addr = 0xcb200000, phy_addr = 0x5b200000
[    4.083440] 3 th virt_addr = 0xcb300000, phy_addr = 0x5b300000
[    4.089252] 4 th virt_addr = 0xcb400000, phy_addr = 0x5b400000
[    4.095060] 5 th virt_addr = 0xcb500000, phy_addr = 0x5b500000
[    4.100868] 6 th virt_addr = 0xcb600000, phy_addr = 0x5b600000
[    4.106688] 7 th virt_addr = 0xcb700000, phy_addr = 0x5b700000
[    4.112499] 8 th virt_addr = 0xcb800000, phy_addr = 0x5b800000
[    4.118301] 9 th virt_addr = 0xcb900000, phy_addr = 0x5b900000
[    4.124109] 10 th virt_addr = 0xcba00000, phy_addr = 0x5ba00000
[    4.129996] 11 th virt_addr = 0xcbb00000, phy_addr = 0x5bb00000
[    4.135897] 12 th virt_addr = 0xcbc00000, phy_addr = 0x5bc00000
[    4.141786] 13 th virt_addr = 0xcbd00000, phy_addr = 0x5bd00000
[    4.147685] 14 th virt_addr = 0xcbe00000, phy_addr = 0x5be00000
[    4.153591] 15 th virt_addr = 0xcbf00000, phy_addr = 0x5bf00000
[    4.159474] 16 th virt_addr = 0xcc000000, phy_addr = 0x5c000000
[    4.165372] 17 th virt_addr = 0xcc100000, phy_addr = 0x5c100000
[    4.171274] 18 th virt_addr = 0xcc200000, phy_addr = 0x5c200000
[    4.177162] 19 th virt_addr = 0xcc300000, phy_addr = 0x5c300000
[    4.183057] 20 th virt_addr = 0xcc400000, phy_addr = 0x5c400000
[    4.188946] 21 th virt_addr = 0xcc500000, phy_addr = 0x5c500000
[    4.194845] 22 th virt_addr = 0xcc600000, phy_addr = 0x5c600000
[    4.200738] 23 th virt_addr = 0xcc700000, phy_addr = 0x5c700000
[    4.206636] 24 th virt_addr = 0xcc800000, phy_addr = 0x5c800000
[    4.212531] 25 th virt_addr = 0xcc900000, phy_addr = 0x5c900000
[    4.218420] 26 th virt_addr = 0xcca00000, phy_addr = 0x5ca00000
[    4.224316] 27 th virt_addr = 0xccb00000, phy_addr = 0x5cb00000
[    4.230211] 28 th virt_addr = 0xccc00000, phy_addr = 0x5cc00000
[    4.236119] 29 th virt_addr = 0xccd00000, phy_addr = 0x5cd00000
[    4.242002] 30 th virt_addr = 0xcce00000, phy_addr = 0x5ce00000
[    4.247896] 31 th virt_addr = 0xccf00000, phy_addr = 0x5cf00000
[    4.256025]  S3C G2D  Init : Done
[    4.257055] S3C CMM Driver, (c) 2008 Samsung Electronics
[    4.263522] s3c_bat_init
[    4.265010] infobowlq-battery infobowlq-battery: s3c_bat_probe
[    4.276226] fg_rcomp_init, rcomp_data[0] : 0xb0
[    4.787004] infobowlq-battery infobowlq-battery: s3c_bat_check_v_f: Unauthori
zed battery!
[    4.791623] infobowlq-battery infobowlq-battery: s3c_set_chg_en: gpio_chg_en(
1) / Charger OFF
[    4.798097] infobowlq-battery infobowlq-battery: s3c_set_time_for_charging: r
eset abs timer
[    4.806420] [FSA9480]get_usb_power_state : usb_power = 2
[    4.806430]
[    4.813194] Unable to handle kernel NULL pointer dereference at virtual addre
ss 00000004
[    4.821372] pgd = c0004000
[    4.824056] [00000004] *pgd=00000000
[    4.827615](        swapper) Internal error: Oops: 805 [#1]
[    4.833157](        swapper) last sysfs file:
[    4.837578](        swapper) Modules linked in:
[    4.842093](        swapper) CPU: 0    Tainted: G        W   (2.6.32.9 #3)
[    4.848953](        swapper) PC is at prepare_to_wait+0x34/0x5c
[    4.854839](        swapper) LR is at get_usb_power_state+0x74/0x104
[    4.861165](        swapper) pc : [<c01fbec8>]    lr : [<c0387fbc>]    psr: 6
0000093
[    4.861174](        swapper) sp : ca023e78  ip : ca023e90  fp : c06d9c1c
[    4.875551](        swapper) r10: c06d9b68  r9 : c06d9b78  r8 : ca023e84
[    4.882227](        swapper) r7 : c06d7fb0  r6 : c066910c  r5 : 00000001  r4
: c06d8028
[    4.890203](        swapper) r3 : 00000000  r2 : 00000001  r1 : ca023e84  r0
: 20000013
[    4.898180](        swapper) Flags: nZCv  IRQs off  FIQs on  Mode SVC_32  ISA
 ARM  Segment kernel
[    4.907022](        swapper) Control: 00c5387d  Table: 50004008  DAC: 0000001

If I boot whithout any connection, the phone stops at displaying the famous "A N D R O I D" tekst, and if I connect it to PC to get an info what's happening - it imidiately reboots. So I am not able to even see what processes are running, what modules are loaded successfully, what errors are, etc.

If anyone gets any idea about the reboot issue, or can provide more info for example about what is xsr and dpram supposed to do (I mean I do not know if I should use those from Acclaim or Spica), I'll be really thankfull

.

---------- Post added at 06:07 PM ---------- Previous post was at 12:42 PM ----------

Ok. The reboot on attaching a cable to USB is probably caused by the fact that fsa9480_codec_probe() is not called at all. GPIO differences between Acclaim and Spica ? Or what ?

**tom3q** · 01-23-2011, 07:48 PM

Originally Posted by gotenks

[ 4.813194] Unable to handle kernel NULL pointer dereference at virtual addre ss 00000004

Looks like something is referencing a NULL pointer. Since prepare_to_wait and get_usb_power_state are both kernel functions and nothing added by Samsung, I guess that the problem starts on a bit higher level. Probably some incorrectly/incompletely filled platform data. Seems like something related with USB. Nothing more can I tell from the log at the moment.

A bit off from the topic:
Did you get the serial cable from somewhere or made it yourself? I'd like to have one as it would be pretty useful, but I don't have time/will/whatever to make one myself.

**gotenks** · 01-23-2011, 07:54 PM

By disabling USB handler I've got the following console output from serial console till the moment when booting stops on displaying "A N D R O I D" on screen. As you can see very little is working

.

Code:

set_ta_status: Disable
display_logo: trying 0x5c400000
display_logo: trying 0x5c400008
display_logo: trying 0x5c400048
display_logo: trying 0x5c400050
display_logo: get_logo_info returns (xres=320, yres=480, size=0x30000)
LoadJPEG: JPEG check (0xFFD8) failed
LoadPNG: width:320, height:480, bpp:24, color_type:2, channels:3, rowbytes:960

Autoboot (0 seconds) in progress, press any key to stop
........................................Done
Kernel read success from kernel partition
setKernelParam: setting param.serialnr=0x3934249a 0x7b8300ec
setKernelParam: setting param.board_rev=0x20
setKernelParam: setting param.cmdline=console=ttySAC2,115200 version=Sbl(1.0.0) 2009-10-15 15:30:37

Starting kernel at 0x50800000...

Uncompressing Linux................................................................................................................................................................................................................. done, booting the kernel.
[    0.000000] Linux version 2.6.32.9 (spica@spica-dev) (gcc version 4.3.4 (crosstool-NG-1.7.0) ) #1 Sun Jan 23 20:25:51 MSK 2011
[    0.000000] CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv6TEJ), cr=00c5387f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine: SCH-R880
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] CPU S3C6410 (id 0x36410101)
[    0.000000] S3C Clocks, (c) 2004 Simtec Electronics
[    0.000000] S3C64XX: PLL settings, A=800000000, M=266000000, E=24000000
[    0.000000] S3C64XX: HCLKx2=266666666, HCLK=133333333, PCLK=66666666
[    0.000000] mout_apll: source is fout_apll (1), rate is 800000000
[    0.000000] mout_epll: source is fout_epll (1), rate is 24000000
[    0.000000] mout_mpll: source is mpll (1), rate is 266000000
[    0.000000] mmc_bus: source is mout_epll (0), rate is 24000000
[    0.000000] mmc_bus: source is mout_epll (0), rate is 24000000
[    0.000000] mmc_bus: source is mout_epll (0), rate is 24000000
[    0.000000] usb-host-bus: source is mout_epll (0), rate is 24000000
[    0.000000] lcd: source is dout_mpll (1), rate is 133000000
[    0.000000] uclk1: source is dout_mpll (1), rate is 66500000
[    0.000000] spi-bus: source is mout_epll (0), rate is 24000000
[    0.000000] spi-bus: source is mout_epll (0), rate is 24000000
[    0.000000] audio-bus: source is mout_epll (0), rate is 24000000
[    0.000000] audio-bus: source is mout_epll (0), rate is 24000000
[    0.000000] irda-bus: source is mout_epll (0), rate is 24000000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 42672
[    0.000000] Kernel command line: console=ttySAC2,115200 version=Sbl(1.0.0) 2009-10-15 15:30:37
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 168MB = 168MB total
[    0.000000] Memory: 162204KB available (4456K code, 1468K data, 1752K init, 0K highmem)
[    0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:229
[    0.000000] VIC @f4000000: id 0x00041192, vendor 0x41
[    0.000000] VIC @f4010000: id 0x00041192, vendor 0x41
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [ttySAC2] enabled
[    0.214331] Calibrating delay loop... 797.90 BogoMIPS (lpj=1994752)
[    0.320128] Mount-cache hash table entries: 512
[    0.322171] CPU: Testing write buffer coherency: ok
[    0.326435] KERNEL:magic_number=66262564 SET_UPLOAD_MAGIC_NUMBER
[    0.332433] (kernel_sec_set_upload_cause) : upload_cause set 0
[    0.342838] NET: Registered protocol family 16
[    0.345939] INFOBOWLQ Machine INIT : Board REV 0x0
[    0.347756] ------------[ cut here ]------------
[    0.352025] WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x50/0xcc()
[    0.359708] autorequest GPIO-131
[    0.362913] Modules linked in:
[    0.365996] [<c01c4eb8>] (unwind_backtrace+0x0/0xe4) from [<c01dc00c>] (warn_slowpath_common+0x4c/0x80)
[    0.375327] [<c01dc00c>] (warn_slowpath_common+0x4c/0x80) from [<c01dc07c>] (warn_slowpath_fmt+0x28/0x38)
[    0.384865] [<c01dc07c>] (warn_slowpath_fmt+0x28/0x38) from [<c03267f0>] (gpio_ensure_requested+0x50/0xcc)
[    0.394487] [<c03267f0>] (gpio_ensure_requested+0x50/0xcc) from [<c03268f0>] (gpio_direction_output+0x84/0xec)
[    0.404462] [<c03268f0>] (gpio_direction_output+0x84/0xec) from [<c000e21c>] (infobowlq_machine_init+0x64/0x29c)
[    0.414596] [<c000e21c>] (infobowlq_machine_init+0x64/0x29c) from [<c000b89c>] (customize_machine+0x1c/0x2c)
[    0.424394] [<c000b89c>] (customize_machine+0x1c/0x2c) from [<c01be384>] (do_one_initcall+0x2c/0x1c0)
[    0.433582] [<c01be384>] (do_one_initcall+0x2c/0x1c0) from [<c0008410>] (kernel_init+0xa0/0x118)
[    0.442340] [<c0008410>] (kernel_init+0xa0/0x118) from [<c01bfee0>] (kernel_thread_exit+0x0/0x8)
[    0.451112] ---[ end trace 1b75b31a2719ed1c ]---
[    0.455818] S3C6410 Power Management, (c) 2008 Samsung Electronics
[    0.461892] ------------[ cut here ]------------
[    0.466457] WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x50/0xcc()
[    0.474141] autorequest GPIO-129
[    0.477347] Modules linked in:
[    0.480425] [<c01c4eb8>] (unwind_backtrace+0x0/0xe4) from [<c01dc00c>] (warn_slowpath_common+0x4c/0x80)
[    0.489761] [<c01dc00c>] (warn_slowpath_common+0x4c/0x80) from [<c01dc07c>] (warn_slowpath_fmt+0x28/0x38)
[    0.499301] [<c01dc07c>] (warn_slowpath_fmt+0x28/0x38) from [<c03267f0>] (gpio_ensure_requested+0x50/0xcc)
[    0.508921] [<c03267f0>] (gpio_ensure_requested+0x50/0xcc) from [<c03268f0>] (gpio_direction_output+0x84/0xec)
[    0.518897] [<c03268f0>] (gpio_direction_output+0x84/0xec) from [<c000e25c>] (infobowlq_machine_init+0xa4/0x29c)
[    0.529032] [<c000e25c>] (infobowlq_machine_init+0xa4/0x29c) from [<c000b89c>] (customize_machine+0x1c/0x2c)
[    0.538829] [<c000b89c>] (customize_machine+0x1c/0x2c) from [<c01be384>] (do_one_initcall+0x2c/0x1c0)
[    0.548015] [<c01be384>] (do_one_initcall+0x2c/0x1c0) from [<c0008410>] (kernel_init+0xa0/0x118)
[    0.556775] [<c0008410>] (kernel_init+0xa0/0x118) from [<c01bfee0>] (kernel_thread_exit+0x0/0x8)
[    0.565520] ---[ end trace 1b75b31a2719ed1d ]---
[    0.592303] S3C6410: Initialising architecture
[    0.639085] bio: create slab <bio-0> at 0
[    0.640818] fsa9480_driver_init
[    0.646257] Bluetooth: Core ver 2.15
[    0.646854] NET: Registered protocol family 31
[    0.648629] Bluetooth: HCI device and connection manager initialized
[    0.655122] Bluetooth: HCI socket layer initialized
[    0.660833] Switching to clocksource clock_source_timer2
[    0.669853] NET: Registered protocol family 2
[    0.670254] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.676810] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.684156] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[    0.690149] TCP: Hash tables configured (established 8192 bind 8192)
[    0.696089] TCP reno registered
[    0.699436] NET: Registered protocol family 1
[    2.337504] [BT] GPIO_BT_HOST_WAKE = 0
[    2.337838] [BT] Device Powering ON
[    2.339187] [BT] GPIO_BT_WLAN_REG_ON = 1
[    2.493113] [BT] GPIO_BT_RST_N = 1
[    2.493293] [BT] GPIO_BT_HOST_WAKE = 1
[    2.494599] [BT] wake_lock timeout = 5 sec
[    2.499075] [BT] Device Powering OFF
[    2.502432] [BT] GPIO_BT_RST_N = 0
[    2.505745] [BT] GPIO_BT_WLAN_REG_ON = 0
[    2.510456] [BT] GPIO_BT_HOST_WAKE = 0
[    2.564056] [BT] GPIO_BT_WAKE = 0
[    2.564090] [BT] wake_unlock(bt_wake_lock)
[    2.616125] [BT] GPIO_BT_WAKE = 0
[    2.616157] [BT] wake_unlock(bt_wake_lock)
[    2.618484] [HEADSET] sec_headset_init
[    2.621953] [HEADSET] sec_headset_probe
[    2.625827] SEC HEADSET: Registering headset driver
[    2.630661] sec_headset_probe IRQ 112 112
[    2.634609] sec_headset_probe xsecond IRQ 122 122
[    2.639959] input: sec_headset as /devices/virtual/input/input0
[    2.646164] SISO:registering switch_sendend switch_dev
[    2.650992] headset irq request end
[    2.653906] [HEADSET] ear_switch_change Headset attached, send end enable 2sec after
[    2.663187] S3C64XX ADC/TS driver, (c) 2009 Samsung Electronics
[    2.667689] s3c_adcts_probe: irq_adc = 95
[    2.671692] S3C64XX ADCTS driver successfully probed !
[    2.676962] kadctsd is started
[    2.679799] S3C PWM Driver, (c) 2006-2007 Samsung Electronics
[    2.685903] IRQ 73/s3c-dmac: IRQF_DISABLED is not guaranteed on shared IRQs
[    2.692396] s3c-dmac: Samsung S3C6410 DMA Controller base address at [phy]:0x75000000, [virt]:0xcb004000, irq 73
[    2.702539] IRQ 74/s3c-dmac: IRQF_DISABLED is not guaranteed on shared IRQs
[    2.709422] s3c-dmac: Samsung S3C6410 DMA Controller base address at [phy]:0x75100000, [virt]:0xcb014000, irq 74
[    2.719598] IRQ 49/s3c-dmac: IRQF_DISABLED is not guaranteed on shared IRQs
[    2.726504] s3c-dmac: Samsung S3C6410 DMA Controller base address at [phy]:0x7db00000, [virt]:0xcb018000, irq 49
[    2.736678] IRQ 50/s3c-dmac: IRQF_DISABLED is not guaranteed on shared IRQs
[    2.743577] s3c-dmac: Samsung S3C6410 DMA Controller base address at [phy]:0x7dc00000, [virt]:0xcb01c000, irq 50
[    2.762386] ashmem: initialized
[    2.797865] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.799396] ROMFS MTD (C) 2007 Red Hat, Inc.
[    2.803166] msgmni has been set to 317
[    2.809577] alg: No test for stdrng (krng)
[    2.810344] io scheduler noop registered
[    2.814023] io scheduler anticipatory registered
[    2.818671] io scheduler deadline registered
[    2.823785] io scheduler cfq registered (default)
[    2.828389] S3C_LCD clock got enabled :: 133.000 Mhz
[    2.842642] Window[0] - FB1: map_video_memory: clear ff000000:00096000
[    2.845597]             FB1: map_video_memory: dma=5a100000 cpu=ff000000 size=00096000
[    2.851471] Window[0] - FB2: map_video_memory: clear ff04b000:0004b000
[    2.857972]             FB2: map_video_memory: dma=5a14b000 cpu=ff04b000 size=0004b000
[    2.873486] Console: switching to colour frame buffer device 40x30
[    2.878235] fb0: s3cfb frame buffer device
[    2.884787] Window[1] - FB1: map_video_memory: clear ff096000:00096000
[    2.890902]             FB1: map_video_memory: dma=5a200000 cpu=ff096000 size=00096000
[    2.896725] Window[1] - FB2: map_video_memory: clear ff0e1000:0004b000
[    2.903218]             FB2: map_video_memory: dma=5a24b000 cpu=ff0e1000 size=0004b000
[    2.913422] fb1: s3cfb frame buffer device
[    2.917689] Window[2] - FB1: map_video_memory: clear ff12c000:00096000
[    2.923738]             FB1: map_video_memory: dma=5a300000 cpu=ff12c000 size=00096000
[    2.933347] fb2: s3cfb frame buffer device
[    2.936085] Window[3] - FB1: map_video_memory: clear ff1c2000:00096000
[    2.942172]             FB1: map_video_memory: dma=57a00000 cpu=ff1c2000 size=00096000
[    2.950480] fb3: s3cfb frame buffer device
[    2.954488] Window[4] - FB1: map_video_memory: clear ff258000:00096000
[    2.960680]             FB1: map_video_memory: dma=57b00000 cpu=ff258000 size=00096000
[    2.968908] fb4: s3cfb frame buffer device
[    2.971739] Registered led device: lcd-backlight
[    3.160281] [HEADSET] send_end_irq_handler  >> 2
[    3.160424] [HEADSET] send_end_enable_timer_handler enable send_end event, token is 1
[    3.167683] [HEADSET] sendend_switch_change  >> 2
[    3.651365] s3c64xx-uart.0: s3c_serial0 at MMIO 0x7f005000 (irq = 16) is a S3C64XX
[    3.654760] s3c64xx-uart.1: s3c_serial1 at MMIO 0x7f005400 (irq = 20) is a S3C64XX
[    3.662412] s3c64xx-uart.2: s3c_serial2 at MMIO 0x7f005800 (irq = 24) is a S3C64XX
[    3.690134] brd: module loaded
[    3.700710] loop: module loaded
[    3.700859] pmem: 1 init
[    3.701971] pmem_render: 0 init
[    3.704936] pmem_stream: 0 init
[    3.708324] pmem_stream2: 0 init
[    3.711550] pmem_preview: 0 init
[    3.714476] pmem_picture: 0 init
[    3.717813] pmem_jpeg: 0 init
[    3.721197] Android kernel panic handler initialized (bind=kpanic)
[    3.726293] PPP generic driver version 2.4.2
[    3.731459] PPP Deflate Compression module registered
[    3.734983] PPP BSD Compression module registered
[    3.741440] PPP MPPE Compression module registered
[    3.744436] NET: Registered protocol family 24
[    3.749027] PPPoL2TP kernel driver, V1.0
[    3.752839] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
[    3.762122] [ADB_UMS_ACM] string_dev = R880249a7b83
[    3.765527] [HEADSET] send_end_release_work_handler  >> Released
[    3.771227] DUN is registerd
[    3.775049] mass_storage_function_add
[    3.777977] fsg_probe pdata: c063eaa4
[    3.781746] android_adb_ums_acm gadget: Number of LUNs=1
[    3.786325] adb_function_add
[    3.790104] android_adb_ums_acm gadget: Android Composite USB, version: Jan 23 2011
[    3.796827] android_adb_ums_acm gadget: android_adb_ums_acm ready
[    3.804236] mice: PS/2 mouse device common for all mice
[    3.809774] [SLIDE] changed Slide state (0)
[    3.813067] input: s3c-keypad-rev0040 as /devices/virtual/input/input1
[    3.819739] s3c-keypad Initialized
[    3.822562] S3C Keypad Driver
[    3.886078] input: optjoy_device as /devices/virtual/input/input2
[    3.890459] S3C RTC, (c) 2004,2006 Simtec Electronics
[    3.891688] s3c_rtc: tick irq 34, alarm irq 92
[    3.896152] s3c-rtc s3c-rtc: rtc disabled, re-enabling
[    3.902827] using rtc device, s3c, for alarms
[    3.905434] s3c-rtc s3c-rtc: rtc core: registered s3c as rtc0
[    3.911685] i2c /dev entries driver
[    3.918561] i2c-gpio i2c-gpio.2: using pins 138 (SDA) and 137 (SCL, no clock stretching)
[    3.924874] i2c-gpio i2c-gpio.3: using pins 36 (SDA) and 35 (SCL, no clock stretching)
[    3.932271] i2c-gpio i2c-gpio.4: using pins 1 (SDA) and 0 (SCL, no clock stretching)
[    3.940444] i2c-gpio i2c-gpio.5: using pins 3 (SDA) and 2 (SCL, no clock stretching)
[    3.946712] s3c-i2c s3c-i2c.0: slave address 0x10
[    3.952865] s3c-i2c s3c-i2c.0: i2c-0: S3C I2C adapter
[    3.955935] s3c-i2c s3c-i2c.1: slave address 0x10
[    3.962547] s3c-i2c s3c-i2c.1: i2c-1: S3C I2C adapter
[    3.966554] Linux video capture interface: v2.00
[    3.980305] Request irq 35 for codec
[    3.980361] Request irq 36 for preview
[    3.983919] S3C FIMC v3.0
[    3.985041] aat1271a_flash_init
[    3.989192] S3C6400 MFC Driver, (c) 2007 Samsung Electronics
[    3.998223] S3C6400 MFC driver module init OK.
[    3.998271] S3C PostProcessor Driver v3.12, (c) 2009 Samsung Electronics
[    4.006714] S3C JPEG Driver, (c) 2007 Samsung Electronics
[    4.013039] S3C G3D Driver, (c) 2007-2009 Samsung Electronics
[    4.016917] s3c_g3d version : 0x1050000
[    4.019342] G3D_RESERVED_MEM_SIZE : 32 MB
[    4.023458] G3D_CHUNK_SIZE : 1 MB
[    4.026673] G3D_CHUNK_NUM : 32 (UI_CHUNK:4)
[    4.030822] 0 th virt_addr = 0xcb000000, phy_addr = 0x5b000000
[    4.036626] 1 th virt_addr = 0xcb100000, phy_addr = 0x5b100000
[    4.042438] 2 th virt_addr = 0xcb200000, phy_addr = 0x5b200000
[    4.048240] 3 th virt_addr = 0xcb300000, phy_addr = 0x5b300000
[    4.054055] 4 th virt_addr = 0xcb400000, phy_addr = 0x5b400000
[    4.059859] 5 th virt_addr = 0xcb500000, phy_addr = 0x5b500000
[    4.065684] 6 th virt_addr = 0xcb600000, phy_addr = 0x5b600000
[    4.071491] 7 th virt_addr = 0xcb700000, phy_addr = 0x5b700000
[    4.077287] 8 th virt_addr = 0xcb800000, phy_addr = 0x5b800000
[    4.083104] 9 th virt_addr = 0xcb900000, phy_addr = 0x5b900000
[    4.088904] 10 th virt_addr = 0xcba00000, phy_addr = 0x5ba00000
[    4.094801] 11 th virt_addr = 0xcbb00000, phy_addr = 0x5bb00000
[    4.100695] 12 th virt_addr = 0xcbc00000, phy_addr = 0x5bc00000
[    4.106589] 13 th virt_addr = 0xcbd00000, phy_addr = 0x5bd00000
[    4.112503] 14 th virt_addr = 0xcbe00000, phy_addr = 0x5be00000
[    4.118383] 15 th virt_addr = 0xcbf00000, phy_addr = 0x5bf00000
[    4.124278] 16 th virt_addr = 0xcc000000, phy_addr = 0x5c000000
[    4.130168] 17 th virt_addr = 0xcc100000, phy_addr = 0x5c100000
[    4.136066] 18 th virt_addr = 0xcc200000, phy_addr = 0x5c200000
[    4.141970] 19 th virt_addr = 0xcc300000, phy_addr = 0x5c300000
[    4.147856] 20 th virt_addr = 0xcc400000, phy_addr = 0x5c400000
[    4.153755] 21 th virt_addr = 0xcc500000, phy_addr = 0x5c500000
[    4.159644] 22 th virt_addr = 0xcc600000, phy_addr = 0x5c600000
[    4.165548] 23 th virt_addr = 0xcc700000, phy_addr = 0x5c700000
[    4.171445] 24 th virt_addr = 0xcc800000, phy_addr = 0x5c800000
[    4.177330] 25 th virt_addr = 0xcc900000, phy_addr = 0x5c900000
[    4.183229] 26 th virt_addr = 0xcca00000, phy_addr = 0x5ca00000
[    4.189118] 27 th virt_addr = 0xccb00000, phy_addr = 0x5cb00000
[    4.195015] 28 th virt_addr = 0xccc00000, phy_addr = 0x5cc00000
[    4.200920] 29 th virt_addr = 0xccd00000, phy_addr = 0x5cd00000
[    4.206807] 30 th virt_addr = 0xcce00000, phy_addr = 0x5ce00000
[    4.212706] 31 th virt_addr = 0xccf00000, phy_addr = 0x5cf00000
[    4.220815]  S3C G2D  Init : Done
[    4.221859] S3C CMM Driver, (c) 2008 Samsung Electronics
[    4.228342] s3c_bat_init
[    4.229791] infobowlq-battery infobowlq-battery: s3c_bat_probe
[    4.241024] fg_rcomp_init, rcomp_data[0] : 0xb0
[    4.751871] infobowlq-battery infobowlq-battery: s3c_bat_check_v_f: Unauthorized battery!
[    4.756487] infobowlq-battery infobowlq-battery: s3c_set_chg_en: gpio_chg_en(1) / Charger OFF
[    4.762955] infobowlq-battery infobowlq-battery: s3c_set_time_for_charging: reset abs timer
[    4.771290] [FSA9480]get_usb_power_state : usb_power = 2
[    4.771300]  [FSA9480] fsa9480_s3c_udc_on : usb_detect_waitq is NULL
[    4.782978] [FSA9480]get_usb_power_state : usb_power=2,taconnection=0
[    4.782989]
[    4.790863] infobowlq-battery infobowlq-battery: s3c_cable_check_status: Unhealth battery state!
[    4.801811] infobowlq-battery infobowlq-battery: s3c_set_chg_en: gpio_chg_en(1) / Charger OFF
[    4.808292] infobowlq-battery infobowlq-battery: s3c_set_time_for_charging: reset abs timer
[    4.821242] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    4.825705] device-mapper: multipath: version 1.1.0 loaded
[    4.830549] device-mapper: multipath round-robin: version 1.0.0 loaded
[    4.837016] device-mapper: multipath queue-length: version 0.1.0 loaded
[    4.843579] device-mapper: multipath service-time: version 0.2.0 loaded
[    4.851576] Bluetooth: Virtual HCI driver ver 1.3
[    4.855875] Bluetooth: HCI UART driver ver 2.2
[    4.859231] Bluetooth: HCI H4 protocol initialized
[    4.864090] Bluetooth: HCI BCSP protocol initialized
[    4.869015] Bluetooth: HCILL protocol initialized
[    4.873666] Bluetooth: Generic Bluetooth SDIO driver ver 0.1
[    4.880043] cpuidle: using governor ladder
[    4.883440] cpuidle: using governor menu
[    4.888667] sdhci: Samsung S3C6410 SD/MMC driver
[    4.892600] s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133333333 Hz)
[    4.898563] s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133333333 Hz)
[    4.905102] s3c-sdhci s3c-sdhci.0: clock source 2: hsmmc (133333333 Hz)
[    4.912771] kimhyuns sdhci_irq_cd lock 1
[    4.915586] sdhci: TFLASH_EN ON
[    4.918699] CARD DETECTION = 1
[    4.922881] Registered led device: mmc0::
[    4.926308] mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using PIO
[    4.932868] s3c-sdhci s3c-sdhci.2: clock source 0: hsmmc (133333333 Hz)
[    4.939362] s3c-sdhci s3c-sdhci.2: clock source 1: hsmmc (133333333 Hz)
[    4.945904] s3c-sdhci s3c-sdhci.2: clock source 2: hsmmc (133333333 Hz)
[    4.953606] Registered led device: mmc1::
[    4.957014] mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using PIO
[    4.973936] [KR3DM] ********** kr3dm_accelerometer_probe =====================
[    4.977300] [KR3DM] ********** i2c_acc_kr3dm_init =====================
[    4.983657] [KR3DM] ********** kr3dm_init =====================
[    4.988123] [KR3DM] i2c_acc_kr3dm_read >>>>>>>>>>>>>>>>>>>>>>>error1<<<<<<<<<<<<<<<<<<
[    4.995986] [KR3DM] i2c_acc_kr3dm_read >>>>>>>>>>>>>>>>>>>>>>>error1<<<<<<<<<<<<<<<<<<
[    5.003829] [KR3DM] i2c_acc_kr3dm_read >>>>>>>>>>>>>>>>>>>>>>>error1<<<<<<<<<<<<<<<<<<
[    5.011723] [KR3DM] i2c_acc_kr3dm_read >>>>>>>>>>>>>>>>>>>>>>>error1<<<<<<<<<<<<<<<<<<
[    5.019603] [KR3DM] i2c_acc_kr3dm_read >>>>>>>>>>>>>>>>>>>>>>>error1<<<<<<<<<<<<<<<<<<
[    5.027499] [KR3DM] i2c_acc_kr3dm_read >>>>>>>>>>>>>>>>>>>>>>>error1<<<<<<<<<<<<<<<<<<
[    5.035375] [KR3DM] i2c_acc_kr3dm_read >>>>>>>>>>>>>>>>>>>>>>>error1<<<<<<<<<<<<<<<<<<
[    5.043269] [KR3DM] i2c_acc_kr3dm_read >>>>>>>>>>>>>>>>>>>>>>>error1<<<<<<<<<<<<<<<<<<
[    5.051161] [KR3DM] i2c_acc_kr3dm_read >>>>>>>>>>>>>>>>>>>>>>>error1<<<<<<<<<<<<<<<<<<
[    5.060754] [AK8973B] this_client is NULL
[    5.065807] logger: created 256K log 'log_main'
[    5.068493] logger: created 256K log 'log_events'
[    5.073754] logger: created 256K log 'log_radio'
[    5.077889] logger: created 64K log 'log_system'
[    5.082541] Advanced Linux Sound Architecture Driver Version 1.0.21.
[    5.093631] No device for DAI AK4671
[    5.093675] No device for DAI s3c-i2s
[    5.096019] AK4671 Audio Codec 0.2
[    5.100569] sound_tty procfs initialised
[    5.102506] sound_tty procfs initialised
[    5.106745] [HEADSET] send_end_irq_handler  >> 1
[    5.112110] asoc: AK4671 <-> s3c-i2s mapping ok
[    5.116379] [HEADSET] sendend_switch_change  >> 1
[    5.140352] [ ak4671.c (set_registers,975) ] Set Audio PATH : 0x02
[    5.140366]
[    5.155303] [HEADSET] get_headset_status  headset_status 1
[    5.181220] [android_ak4671] android_snd_device add fail
[    5.181267] ALSA device list:
[    5.183972]   #0: android (AK4671)
[    5.188307] Netfilter messages via NETLINK v0.30.
[    5.192223] nf_conntrack version 0.5.0 (2536 buckets, 10144 max)
[    5.199709] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[    5.205470] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[    5.213315] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[    5.219870] xt_time: kernel timezone is -0000
[    5.223878] IPv4 over IPv4 tunneling driver
[    5.229458] GRE over IPv4 tunneling driver
[    5.233420] ip_tables: (C) 2000-2006 Netfilter Core Team
[    5.237617] TCP cubic registered
[    5.245034] NET: Registered protocol family 10
[    5.247102] IPv6 over IPv4 tunneling driver
[    5.250434] NET: Registered protocol family 17
[    5.253636] Bluetooth: L2CAP ver 2.14
[    5.257166] Bluetooth: L2CAP socket layer initialized
[    5.262194] Bluetooth: SCO (Voice Link) ver 0.6
[    5.266716] Bluetooth: SCO socket layer initialized
[    5.273292] mmc0: new high speed SDHC card at address 7323
[    5.277682] blk_queue_max_sectors: set to minimum 8
[    5.282547] mmcblk0: mmc0:7323 SD04G 3.69 GiB
[    5.286623]  mmcblk0:
[    5.288643] Bluetooth: RFCOMM TTY layer initialized
[    5.293505] Bluetooth: RFCOMM socket layer initialized
[    5.298534] Bluetooth: RFCOMM ver 1.11
[    5.304355] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
[    5.313530]  p1 p2
[    5.315991] Filed to request GPIO_TOUCH_EN!
[    5.625292] i2c_smbus_read_byte_data failed
[    5.625337] melfas_ts_probe: Firmware Version fffffffa
[    5.635261] i2c_smbus_read_word_data failed
[    5.645243] i2c_smbus_read_word_data failed
[    5.645310] melfas_ts_probe: max_x 320, max_y 480
[    5.649618] input: melfas_ts_input as /devices/virtual/input/input3
[    5.656025] melfas_ts_probe: Start touchscreen melfas_ts_input
[    5.661348] s3c-rtc s3c-rtc: setting system clock to 2011-01-23 00:00:10 UTC (1295740810)
[    5.669841] Freeing init memory: 1752K
[    5.672654] Warning: unable to open an initial console.
[    5.677946] melfas_ts_work_func: i2c_transfer failed
[    5.720264] [HEADSET] send_end_press_work_handler  >> Pressed
[    5.726157] init: /init.rc: 315: user option requires a user id
[    6.613259] init: cannot open '/initlogo.rle'
[    6.625611] xsr: module license 'Samsung Proprietary' taints kernel.
[    6.626335] Disabling lock debugging due to kernel taint
[    6.671508] [ONLD] =============== OCLD local mode ===============
[    6.672147] [ONLD] LLD VERSION : OCLD_v1.0.0_XSR1.5.2p4_Linux_090427
[    6.678652] [ONLD] OND_TRANS_MODE = 0x2 with    CacheRead
[    6.684083] [ONLD] Enable  ONENANDCON_READ_FULL_SECTOR
[    6.689256] [ONLD] Disable ONENANDCON_WRITE_FULL_SECTOR
[    6.694545] [ONLD] Enable  DEFERRED_CHK
[    6.698445] [ONLD] ===============================================
[    6.756002] [BBM:   ]  << DevNO:0 MAPPING INFORMATION >>
[    6.756044] [BBM:   ]   Bad Mark Information
[    6.760101] [BBM:   ]      - Bad Mark (0x22) by write error
[    6.765813] [BBM:   ]      - Bad Mark (0x11) by erase error
[    6.771414] [BBM:   ]   pstDev->n1stSbnOfULArea = 0
[    6.776440] [BBM:   ]   000: Sbn[1298] ==> Rbn[4014] / UnLocked / BadMark:0x00
[    6.783649] [BBM:   ]   << Total : 1 BAD-MAPPING INFORMATION >>
[    6.807269] XSR: Registered BML Driver.
[    6.840182] [OneDRAM] dpram_probe:2671 - sime_state = 0
[    6.841251] [OneDRAM] register_interrupt_handler:2594 - sim detect interrupt handler failed.
[    6.848265] ------------[ cut here ]------------
[    6.852805] WARNING: at kernel/irq/manage.c:858 __free_irq+0x90/0x1a0()
[    6.859364] Trying to free already-free IRQ 105
[    6.863870] Modules linked in: dpram(+) xsr(P)
[    6.868340] [<c01c4eb8>] (unwind_backtrace+0x0/0xe4) from [<c01dc00c>] (warn_slowpath_common+0x4c/0x80)
[    6.877671] [<c01dc00c>] (warn_slowpath_common+0x4c/0x80) from [<c01dc07c>] (warn_slowpath_fmt+0x28/0x38)
[    6.887206] [<c01dc07c>] (warn_slowpath_fmt+0x28/0x38) from [<c0208b34>] (__free_irq+0x90/0x1a0)
[    6.895961] [<c0208b34>] (__free_irq+0x90/0x1a0) from [<c0208c80>] (free_irq+0x3c/0x5c)
[    6.903976] [<c0208c80>] (free_irq+0x3c/0x5c) from [<bf02b7c4>] (register_interrupt_handler+0x108/0x178 [dpram])
[    6.914108] [<bf02b7c4>] (register_interrupt_handler+0x108/0x178 [dpram]) from [<bf02dd80>] (dpram_probe+0x3dc/0x564 [dpram])
[    6.925369] [<bf02dd80>] (dpram_probe+0x3dc/0x564 [dpram]) from [<c03600b8>] (platform_drv_probe+0x1c/0x24)
[    6.935061] [<c03600b8>] (platform_drv_probe+0x1c/0x24) from [<c035f0a4>] (driver_probe_device+0x78/0x184)
[    6.944681] [<c035f0a4>] (driver_probe_device+0x78/0x184) from [<c035f23c>] (__driver_attach+0x8c/0x90)
[    6.954042] [<c035f23c>] (__driver_attach+0x8c/0x90) from [<c035e914>] (bus_for_each_dev+0x60/0x8c)
[    6.963058] [<c035e914>] (bus_for_each_dev+0x60/0x8c) from [<c035e170>] (bus_add_driver+0x9c/0x248)
[    6.972074] [<c035e170>] (bus_add_driver+0x9c/0x248) from [<c035f4e0>] (driver_register+0x70/0x15c)
[    6.981098] [<c035f4e0>] (driver_register+0x70/0x15c) from [<c01be384>] (do_one_initcall+0x2c/0x1c0)
[    6.990199] [<c01be384>] (do_one_initcall+0x2c/0x1c0) from [<c0203dcc>] (sys_init_module+0xc8/0x1fc)
[    6.999301] [<c0203dcc>] (sys_init_module+0xc8/0x1fc) from [<c01beee0>] (ret_fast_syscall+0x0/0x2c)
[    7.008306] ---[ end trace 1b75b31a2719ed1f ]---
[    7.013051] dpram-device: probe of dpram-device failed with error -1
[    7.061187] [BIF:WRN] BML_Init is already called
[    7.111430] [BBM:   ]  << DevNO:0 MAPPING INFORMATION >>
[    7.111473] [BBM:   ]   Bad Mark Information
[    7.115604] [BBM:   ]      - Bad Mark (0x22) by write error
[    7.121214] [BBM:   ]      - Bad Mark (0x11) by erase error
[    7.126837] [BBM:   ]   pstDev->n1stSbnOfULArea = 0
[    7.131872] [BBM:   ]   000: Sbn[1298] ==> Rbn[4014] / UnLocked / BadMark:0x00
[    7.139072] [BBM:   ]   << Total : 1 BAD-MAPPING INFORMATION >>
[    7.161375] XSR: Registered STL Driver.
[    7.249131] [BBM:   ]  << DevNO:0 MAPPING INFORMATION >>
[    7.249173] [BBM:   ]   Bad Mark Information
[    7.253290] [BBM:   ]      - Bad Mark (0x22) by write error
[    7.258930] [BBM:   ]      - Bad Mark (0x11) by erase error
[    7.264549] [BBM:   ]   pstDev->n1stSbnOfULArea = 0
[    7.269570] [BBM:   ]   000: Sbn[1298] ==> Rbn[4014] / UnLocked / BadMark:0x00
[    7.276784] [BBM:   ]   << Total : 1 BAD-MAPPING INFORMATION >>
[    7.296964] [VIBETONZ] vibetonz_start :
[    7.297007] Failed to request GPIO_VIB_EN!
[    7.364184] [BBM:   ]  << DevNO:0 MAPPING INFORMATION >>
[    7.364226] [BBM:   ]   Bad Mark Information
[    7.368356] [BBM:   ]      - Bad Mark (0x22) by write error
[    7.373961] [BBM:   ]      - Bad Mark (0x11) by erase error
[    7.379593] [BBM:   ]   pstDev->n1stSbnOfULArea = 0
[    7.384624] [BBM:   ]   000: Sbn[1298] ==> Rbn[4014] / UnLocked / BadMark:0x00
[    7.391831] [BBM:   ]   << Total : 1 BAD-MAPPING INFORMATION >>
[    7.532624] rfs_build_sb[338]: invalid boot sector signature (aa55 != 0)
[    7.875143] [STL:ERR] Partition is already opened (Vol 0, Part 5)
[   10.267277] [STL:ERR] Partition is already opened (Vol 0, Part 5)
[   10.269066] [STL:ERR] Partition is already opened (Vol 0, Part 5)
[   10.376101] rfs_build_sb[338]: invalid boot sector signature (aa55 != 0)
[   10.585876] [STL:ERR] Partition is already opened (Vol 0, Part 4)
[   15.083284] [STL:ERR] Partition is already opened (Vol 0, Part 4)
[   15.085015] [STL:ERR] Partition is already opened (Vol 0, Part 4)
[   15.092056] init: cannot execve('/xbin/busybox'): Bad address
[   15.097309] init: cannot execve('/xbin/busybox'): Bad address
[   15.103575] init: cannot execve('/xbin/busybox'): Bad address
[   15.108769] init: cannot execve('/xbin/busybox'): Bad address
[   15.114496] init: cannot execve('/xbin/busybox'): Bad address
[   15.120813] init: cannot execve('/xbin/busybox'): Bad address
[   15.198009] rfs_build_sb[338]: invalid boot sector signature (aa55 != 0)
[   15.318330] [STL:ERR] Partition is already opened (Vol 0, Part 6)
[   15.887624] [STL:ERR] Partition is already opened (Vol 0, Part 6)
[   15.889350] [STL:ERR] Partition is already opened (Vol 0, Part 6)
[   15.949617] __log_replay[1141]: RFS_SUBLOG_COMMIT (0,8a:0a)
[   15.949974] rfs_fill_super[200]: RFS successfully mounted [8a:0a]
[   16.022827] [UART Switch] Path : PDA
[   16.072446] init: wifi.mac_addr: check_wifi_address()
[   16.072917] init: wifi.mac_addr: .mac.info already exist!
[   16.079917] [adb_function_enable] adb_function => (enabled)
[   16.082885] [acm_function_enable] acm_function => (enabled)
[   16.088411] [s3c_udc_pullup] is_on[0]
[   16.092015] [s3c_udc_power_down] skipped , already powered off
[   16.121723] [s3c_udc_pullup] is_on[1]
[   16.121758] [FSA9480]fsa9480_check_usb_connection
[   16.121766]  [FSA9480] control(0xc0) int1(0x50) adc(0x0) dev1(0xc0) dev2(0x0) man1(0x0) man2(0x0) pwr(2)
[   16.133956] [FSA9480] AUTO MODE.. d1:0xc0, d2:0x00
[   16.138693] [FSA9480]fsa9480_s3c_udc_off
[   16.138703]  [STL:ERR] Partition is already opened (Vol 0, Part 5)
sh: can't access tty; job control turned off
# [   17.523249] warning: `rild' uses 32-bit capabilities (legacy support in use)
[   19.324024] [AK4671] Set bitRate : 0xf8 (44100)
[   19.351235] [ ak4671.c (ak4671_set_path,474) ] path_state : 0x02, input path = 0x02
[   19.353347] [ ak4671.c (ak4671_mute,765) ] mute is not supported (0)
[   19.378843] [ ak4671.c (ak4671_set_idle_mode,343) ]  idle_mode_value : 1
[   30.923792] request_suspend_state: wakeup (3->0) at 30508596596 (2011-01-23 00:00:35.762446518 UTC)
[   30.929712] [ ak4671.c (ak4671_mute,765) ] mute is not supported (1)
[   30.934543] init: untracked pid 2120 exited
[   31.890379] [ ak4671.c (ak4671_set_path,474) ] path_state : 0x02, input path = 0x02
[   31.892403] [HEADSET] get_headset_status  headset_status 1
[   31.970372] [ ak4671.c (ak4671_mute,765) ] mute is not supported (0)
[   31.977373] [ ak4671.c (ak4671_set_idle_mode,343) ]  idle_mode_value : 1
[   31.978444] [ ak4671.c (ak4671_set_idle_mode,359) ] invalid idle mode value
[   41.307717] request_suspend_state: wakeup (0->0) at 40892521304 (2011-01-23 00:00:46.146371046 UTC)
[   41.313570] [ ak4671.c (ak4671_mute,765) ] mute is not supported (1)
[   41.318933] init: untracked pid 2151 exited
[   42.265377] [ ak4671.c (ak4671_set_path,474) ] path_state : 0x02, input path = 0x02
[   42.267399] [HEADSET] get_headset_status  headset_status 1
[   42.340372] [ ak4671.c (ak4671_mute,765) ] mute is not supported (0)
[   42.347941] [ ak4671.c (ak4671_set_idle_mode,343) ]  idle_mode_value : 1
[   42.349011] [ ak4671.c (ak4671_set_idle_mode,359) ] invalid idle mode value
[   52.063101] request_suspend_state: wakeup (0->0) at 51647905937 (2011-01-23 00:00:56.901755514 UTC)
[   52.069472] [ ak4671.c (ak4671_mute,765) ] mute is not supported (1)
[   52.073845] init: untracked pid 2176 exited
[   53.060380] [ ak4671.c (ak4671_set_path,474) ] path_state : 0x02, input path = 0x02
[   53.062405] [HEADSET] get_headset_status  headset_status 1
[   53.125374] [ ak4671.c (ak4671_mute,765) ] mute is not supported (0)
[   53.132301] [ ak4671.c (ak4671_set_idle_mode,343) ]  idle_mode_value : 1
[   53.133371] [ ak4671.c (ak4671_set_idle_mode,359) ] invalid idle mode value
[   62.440901] request_suspend_state: wakeup (0->0) at 62025706202 (2011-01-23 00:01:07.279555704 UTC)
[   62.446763] [ ak4671.c (ak4671_mute,765) ] mute is not supported (1)

---------- Post added at 06:54 PM ---------- Previous post was at 06:50 PM ----------

Hi tom3q,

Originally Posted by gotenks

Ok. The reboot on attaching a cable to USB is probably caused by the fact that fsa9480_codec_probe() is not called at all. GPIO differences between Acclaim and Spica ? Or what ?

Here seems to be a problem. But not the only one. See my other console output above

.

**tom3q** · 01-23-2011, 07:54 PM

Now it looks like it gets a wrong partition table or something. Not saying anything about drivers bugs (freeing already free irqs or autorequesting GPIOs), because it should be irrelevant.

**gotenks** · 01-23-2011, 08:01 PM

Originally Posted by tom3q

Now it looks like it gets a wrong partition table or something. Not saying anything about drivers bugs (freeing already free irqs or autorequesting GPIOs), because it should be irrelevant.

Then it must be a problem with xsr (and maybe dpram) modules. I've used xsr from Acclaim so probably here is an explanation.

EDIT
I have to stop playing with Acclaim's kernel now because Spica is my daughter's phone and she requested to give it back.

**rapasamdroid** · 01-23-2011, 09:15 PM

Love that comment :-)

[QUOTE
EDIT
I have to stop playing with Acclaim's kernel now because Spica is my daughter's phone and she requested to give it back.[/QUOTE]

**gotenks** · 01-23-2011, 10:09 PM

Originally Posted by tom3q

A bit off from the topic:
Did you get the serial cable from somewhere or made it yourself? I'd like to have one as it would be pretty useful, but I don't have time/will/whatever to make one myself.

I've made it myself from "modules" bought on Allegro and in an internet electronic shop

. I bought TTY->RS232 converter, built on ST3232, ready to plug into PC's COM on Allegro, and I bought a MicroUSB B connector in a shop. I soldered both parts with a cable, putting a resistor between pins 4 and 5 and it magically started to work

. Exactly as described here An odd Serial Port on Spica (FSA9480 attached)

---------- Post added at 09:09 PM ---------- Previous post was at 09:08 PM ----------

Originally Posted by rapasamdroid

Love that comment :-)

Yeah ... daughters ... better not to make them angry

**|X|S|6|2|1|** · 01-25-2011, 11:58 AM

btw,:

machine : SCH-R880 <- are you not wrong ? isnt that supposed to be machine : GT-i5700 ?

**gotenks** · 01-25-2011, 02:46 PM

Originally Posted by |X|S|6|2|1|

machine : SCH-R880 <- are you not wrong ? isnt that supposed to be machine : GT-i5700 ?

No, I am not

. I took the shortest way to achive a goal. And the goal was to see if the Acclaim's kernel can run at all. Besides, this is only a log - you do not have to care about this issue at all

.

Now I have to wait until I will be able to play with my daughter's Spica again to make more tests

. I am planning to check, if using original Acclaim's xsr module I will be able to properly mount /system and /data. However there is one thing I have to check first. I have to check what bml devices are available using Acclaim's xsr module. This is the most important, because as far as I can tell, not all Spica_like phones have all ten bml devices

.